Saturday, 26 October 2013

Apple Blossom

Hi all,

I spent much of this week finishing off another box. This one was cut from a piece of mahogany and features scroll sawing on the ends.

And on the front and back.

Care was taken when cutting out each petal because the design I came up with needed only a thin piece of wood between each petal. The total number of petals to be cut out was 60 and I'm afraid that my concentration began to wain as I approached the end and I got a kick back. This incident broke the piece of wood that separated too petals. I swore a little when it happened, but it could have been worse, at least I didn't cut a finger off.

Kick backs are quite common when using a scroll saw and this is especially so when using reverse blades. Because the teeth at the bottom of the blade point upwards it means that the wood can be lifted by the blade and, if it isn't being held firmly enough, the wood bounces about on the table in an alarming manner. For this reason it is often referred to as table slap. To prevent table slap, all scroll saws are fitted with a piece of metal to hold the wood in place. The only trouble is it gets in the way so most scroll sawers, including me, end up ditching it.

Anyway, I was making the box for my own use so it didn't matter as much as it would if I was intending to selling it. This box was to be a prototype for my foray into inlay work using polymer clay.

The design for the lid of the box was cut out in much the same way as the sides and ends and the holes underneath were covered with a piece of 3mm ply wood. This was glued into place and clamped to make sure it was a tight seal. When it was dry I mixed up some polymer clay and pressed it into the holes in the wood with a craft knife.

For the branches I used white, translucent and a very small  amount of black clay. While for the flowers I used white, translucent, and pink. The make of clay used was sculpey premo. Once the holes had been filled with clay I baked the lid for 30 minutes following the instructions on the packet.
Here is the finished lid.

When it came out of the oven I was surprised to find that the clay had raised itself a little, but this was soon rendered flush by giving it a couple of seconds on my belt sander. I then finished the lid and the rest of the box with a wax polish.

All in all, I think my first attempt at a proper inlay was a a success. With hindsight I would have not made the flowers quite so pink and I would have mixed a little brown in the colour used for the branches instead of black.

In my next post I will show you a couple of boxes that I have made that have fallen to the heat of my pyrography iron. But for now I must get back to the packing. We will be moving house in a couple of weeks and a lot needs to be done.

Thursday, 17 October 2013

Walnut box finished at last

Hi all, sorry about the delay in getting this post out, but we are hoping to move house soon and preparations for that are not only abundant, but they they also have priority.

Anyway, here's how I finished the walnut box. After sticking the fronts and sides together I did a design for the lid that carried on with the fuchsia theme.
I left a small space in the middle for a knob which I had intended to make from clay. However, rolling a small ball of clay into a perfectly round sphere is something beyond me, and, seeing as I wanted the box to look special, I decided to make one out of a tiny bit of scrap walnut.

Cutting the lid on the scroll saw required a lot of concentration because in some places the design called for narrow pieces of wood. Still it all went well and I was soon burning in the fuchsias with my pyrography iron. Once that was done I gave the whole box a rub down with fine sand paper and then a coat of sanding sealer.

The box was finally finished with three coats of varnish and some nice felt was stuck to the bottom by an expert box felter (my wife) who does a fantastic job.
Here is the finished box prior to the felting. I was going to sell it on folksy, but like a lot of stuff I have been doing recently, my wife bagsied it for the house. Ah well, you can't win them all. My next project is another box that will be made from Mahogany. It will have an apple blossom design and will have a lid which has been inlaid with clay.

If I can just get on top of these moving house tasks, I hope to show it to you soon.


Wednesday, 9 October 2013

Happy Little Pot

Hi all,
Sorry if you are expecting the last instalment of the walnut box, but there has been a change of plan. When I started doing pyrography I was pleased with how quick I could produce something that gave me pleasure.

However, I have recently been making my own boxes on a scroll saw and, although they do provide a lot of satisfaction when completed, they are quite a long while in the making. Depending on how much free time I have available it can sometimes take up to 3 weeks to complete 1 box and that is frustrating.

Over the years, I have often pondered the issue regarding what makes me happy. If you take away the thorny subject of money, happiness is an elusive commodity. For many years I thought the route to happiness was through contentment. If one could be satisfied with ones lot and not always be coveting what others had got, it should lead one to happiness. This theory is good to a point, but when one is sitting in ones chair how do you give yourself a little boost?

I don't know about anybody else, but for me it is achieving something or making something, and that is why pyrography is so good. I was 2 weeks into the walnut box and wondering if I'd ever finish it when I decided a quick shot of achievement would be good. So I immediately turned to my pyrography iron.

I looked at my blanks and found a small trinket box that I had purchased a few moths ago and set about creating a pattern on it with my pyrography iron. I didn't pencil it in first, I just went for it with the iron and hoped for the best.
One hour later, I had created something that I was very pleased with and that is where a lot of my pleasure comes from with pyrography. Now all I have to do is upload it to folksy.com and see if anybody else likes it as well.

In my next post I'm looking forward to showing you the finished walnut box.

Tuesday, 1 October 2013

Walnut Box Part 3 and a free book

Hi all,
In my last post I mentioned the main difference regarding scroll saw blades and I will repeat it here just for the purpose of any new readers. If you are thinking of buying a scroll saw, make sure you get one that will take plain end blades. Pin end blades are useless for any detailed fretwork.

Besides various sizes of blade, mentioned in my last post, there are other attributes to consider when choosing a blade for a certain project. Some blades just a have a straight row of teeth, while others have every other saw tooth missing, these are called skip tooth blades. Then there are reverse tooth blades where the bottom few teeth point in the opposite direction. I use reverse tooth blades because they prevent tear out on the bottom side of the wood. If this is the case I can't think why I would want to use a skip tooth blade. Apparently they cut faster, but if you see how quick a decent scroll saw goes you may wonder at the logic in trying to go any faster, especially if it leads to torn out grain at the bottom of the saw cut. Saving micro seconds on the sawing and then having to spend a lot of time sanding the torn out grain on the underneath of the project doesn't seem like a reasonable payoff to me.

Anyway, back to the box. Here is a view of one of the ends after the scroll work has been done. You will also notice that I have used my pyrography iron to separate the flowers. 
Here is a little observation. When it comes to doing a bit of pyrography on most woods the smell that is created is what you would expect. It smells like wood burning, which thankfully isn't too unpleasant, that is as long as your name isn't Guy Fawkes or Joan of Arc.

Anyway, be aware that walnut smells pretty grim when it is being burnt with a pyrography iron. It has a  pong like gone-off kippers. Despite having my extractor fan on and the window open in my workshop, by the time I'd finished doing the pyrography, I smelt like an Arbroath Smokie.

After all the sizes were cut, burnt and sanded I stuck the box together with wood glue and clamped them together

Here are the four sides complete.
The next step was to cut a piece of wood for the base and after that I started to work on the design for the lid. I will show you that in my next post.

By the way. if you are interested in a free book. One of mine called Bossyboots is available as a free download on smashwords.com. Just click here and enter the following coupon code at the check out TK32S.

Tuesday, 24 September 2013

Scroll saw walnut box part 2

Hi All,
Carrying on from last week regarding the walnut box here is the next step. I took the image of the single fuchsia and copied it.
Then I pasted it several times into a new image and moved each one about until I came up with something that I liked.
I then printed off the image and made some more alteration by hand. For instance, the three fuchsia an the left would be left dangling once the wood had been cut away, so I joined them to the bottom of the wood via the stamens.

I find that when doing a pattern for cutting that it becomes a lot clearer if I colour the wood that is to be removed with the scroll saw. Please see the picture below; the areas in blue are the ones that will be cut out.
 The design is now stuck onto the wood with temporary spray adhesive and I have drilled the entry holes for the scroll saw blades. You can also see, on both edges, the markings for the box joints which I will cut out first.

I have also made some notes on the drawing regarding blade sizes and before we go any further this would be a good point to give you some information on scroll saw blades, especially if you are thinking of investing in a scroll saw.

Firstly, there are two types of scroll saw blade; plain end and pin end. Whatever you do, please make sure your saw takes plain end blades. Do not, I repeat, do not buy a saw which takes pin end blades only. The reason for this is when you are making inside cuts you will have to thread your saw blade through the wood via drilled holes. If you look at the drilled holes between the stamens, you will see that they are very small and a pin end blade won't go through small holes or even reasonably big holes.

The second thing you need to take into account when purchasing a saw is, how easy is it going to be to unclamp the blade and re-thread it through the wood for every section in the design you are working on. If you take the design above, the blade needs to be threaded through the holes 17 times and that is just for one side of the box. So, quick release clamps are almost a must if you are going to take scroll sawing seriously. Just imagine messing about with screwdrivers or other tools every time you want to cut a new section. By the time I have finished this box I will have clamped and unclamped the blade at least 80 times and that is without changing the blades to do the box joints.

Now you may be wondering at this point why it would be necessary to change the blade when doing the box joints because it looks like a straight forward outside cut. Well it is, but bigger blades cut straighter lines. Here is a picture of blades at both ends of the spectrum. A number 1, which is the thinnest and a number 12 which is the biggest.
So, when I make the horizontal cuts on the edges of the design I use a number 12 blade to give me the straightest possible line. And, to save me changing blades too often, I do the horizontal cuts on all four sides of the box while I have the number 12 blade in the saw.

Now here is the clever bit. When it comes to making the vertical cut I can get out of trying to saw around the sharp corner by using a number 1 blade. This blade is so thin that it will actually slide sideways down the space made by the number 12 blade. The result is that I can quickly make the vertical cuts without the need to cut any corners. Care does need to be taken to get the cut as straight as possible, but it is only a small distance so is pretty easy.

I hope all that makes sense. Please let me know if you need any clarification. In my next post I will tell you about the type of blade I prefer and will show you how I got on after cutting the wood. There should also be a bit of pyrography in there too.

Tuesday, 17 September 2013

Walnut Box

Hi All,
Firstly, regarding the title of this post. I'd like to point out that it concerns a box made from walnut wood and not a box to keep walnuts in.

Anyway, I had this idea to make a box with my scroll saw and decorate it with a design of fuchia flowers. I would burn the flowers into the wood with my pyrography iron and then paint them. The box would have fret work sides and top and as such should be suitable as a pot-pourri container.

One of the main reasons for purchasing a scroll saw was the scope it would give me in making boxes for my pyrography work and I thought this project would be good practice. Over the next three or four posts I will go through the process in detail, from the purchase of the wood to the completed project.

The starting point with any project revolving a scroll saw or pyrography is in acquiring some wood, so I purchased a small plank of walnut measuring 4inches by 18 inches from a company called Hobbies.com. The plank of wood is 6mm thick (about a quarter of an inch) and believe it or not but that is the largest plank of hardwood of that thickness that I can find anywhere. If anybody knows a source of bigger pieces of quarter inch hardwood please let me have the details.

By the way, this was the first time I'd worked with walnut and have to say I was a bit disappointed by its appearance. The tables and other items I've seen on the antiques road show that have been made from walnut always look fantastic and they made the piece of wood I'd received look some what dowdy by comparison. Perhaps it will look much better when it has been finished off. I do hope so because this sniffling little piece of wood cost me almost a fiver.

Once the wood arrived I designed the overall shape of the box on it. Once it was divided up into the six parts that make up a box I could then start working on the design. Here is the plank of walnut after I  divided it the parts for the box.
I would concentrate on the front and sides of the box first, so that was where my design began. I measured the size of the front and opened a new blank file in adobe photoshop to that exact size.
I then drew a image of a fuchia with a pencil onto a piece of paper. I used a pencil so that I could keep rubbing the image out until I was happy with it. When I finally had a stylised image of a fuchia that I thought would suit my needs, I went over image with a pen and then scanned it into my computer.

Okay, so perhaps it isn't the most spectacular fuchia you ever did see and it won't win any prizes at the Chelsea flower show, but I have every faith that it will look good on the finished box. Once the fuchia was in the computer it was a simple matter of copying the image and pasting it into the the blank file I had opened earlier.

This is the way I do most of my design work and I will go on to explain the next steps in my next post.

Tuesday, 10 September 2013

Blade Draws

Hi All,
When I started scroll sawing, finding somewhere to store my blades wasn't an issue because I only had the few blades that came with the saw. However, every time I started a new project I had to purchased more and more blades to suit the size of the wood I was going to be cutting.So I soon had lots of blades ranging from size 1 to size 12 with 12 being the biggest. You may think it is obvious that size 12 is the biggest, but that rule doesn't alway apply. With fishing hooks, for instance, the higher the number is, the small the hook is. You could hang a dead pig on size 1 hook, but you could thread a size 26 through the eye of a needle.

Anyway, with my blades in danger of getting into a dire mess, I decided to make a small set of draws to keep them in. And while I was at it, I would include a draw for my junior hacksaw blades and my Stanley knife blades.

I cut the main structure from a piece of 15mm pine and made the drawer fronts and sides from 6mm pine strip. The bases of the drawers were cut from 3mm plywood. The wood I used was all stuff lying around my workshop, so I guess I made the whole thing for free. Everything was cut on my scroll saw so there wasn't any hard work involved in the project, which is great because sawing a lot of wood by hand is very tedious.

Originally, I had intended on using my pyrography iron to burn the blade sizes onto each drawer but I decided against the idea. The draw knobs were kindly made by my wife from clay and I painted them blue.

Here is a picture of the finished set of drawers.

Considering I didn't take too much time over making this item I am pleased with the results. It looks good and it is useful, so in my book that counts as a success.

Another good thing that came out of the project was my first encounter with 'sanding sealer'. I first heard about this product almost fifty years ago when I was a young lad who enjoyed making model air planes from balsa wood. The sad thing is that the only money I had in the world, in those days, came from my paper round, so I only bought necessities and 'sanding sealer' was deemed a luxury too far.

As it happens nothing much has changed in my life and I still don't like to fritter money away, but seeing as there was a lot of open end grain on the pine I was using, I decided to give it a go.

The result was brilliant. I used it after the final sanding, it really does improve the finish. If I'd known how good it was all those years ago I might have risked thruppence on a bottle.