Hi all,
Just a quick one. When I purchased my scroll saw I had only intended to use it for craft purposes, making boxes and the like. However, due to moving house I have found myself swamped with DIY tasks. Not least the revamping of the bathroom from hell.
Even after we'd had a new shower and bathroom suite fitted, and had the numerous leaks fixed there was still much work to be done. For the record, the leaks were caused by plumbers and not me. Anyway, my wife wanted shelves around two walls and because the plastic bath panel that came with the bath was much less useful than an ashtray on a motorbike, I decided that I would panel the bath with some tongue and groove.
All of this meant that a lot of wood needed cutting, so I press ganged the scroll saw, which had been sulking in the corner for a few months feeling very unwanted, into action.
First, I designed and cut out a set of 8 shelf brackets and finished them off with my bobbin sander. Making the brackets was quite enjoyable because it reminded me of my previous life in a factory where the production line was king. Here is a photo before I varnished them.
Before I show you a photo of the finished bathroom, here is one when it was at its lowest ebb. I was in the process of taking up the laminate flooring which was in an awful state.
It took a long time but eventually I did manage to finish the bathroom and due to my wife's interior decorating skills I think it came out rather well. The finished bathroom can be seen below and you may note that there isn't a single tile in sight.
The reason there are no tiles is because we both think that they make bathrooms very cold and clinical. Over the last few years there has been a general increase in the use of tiles, from a couple of rows over the bath to having a bathroom completely tiled. Fashion now dictates that everyone should have a wet room with a plug in the middle of the floor to let the water out.
I used a wet room at the hospital when I was recovering from a heart attack and a grim place it was too. We asked ourselves what we were going to be washing in our bathroom and how much splashing there would be. We mainly use the shower with the bath being reserved for Daisy our dog so splashing isn't an issue for us. If we had a pet hippo that required a regular sluicing down, a wet room might be an option but for now, cosy will do for us.
Sunday, 11 May 2014
Sunday, 4 May 2014
A Two Draw Box
Hi all,
Sorry it's been a long time between posts but I seem to have found a task that is taking all my time and then some more. I am talking about the new bathroom in the bungalow we have moved into. We had a new shower and bathroom suite fitted and in between several leaks (left by the plumbers I hasten to add) I have been doing the decorating making shelves etc which I will show you in my next post.
I may not have been using my scroll saw for craft purposes but I have been using it continuously to help with the DIY jobs.
Anyway, this week I an determined to do a scroll saw box and a bit of pyrography. The box is of my own design and a bit of an experiment because this will be my first two draw box.
I thought it would be cute to make it resemble a smiling face and I will be interested to see how it looks when it is complete. I will be making this one out of a plank of pine that was one of the side rail of my mother in law's old bed so it will be a freebee which is very nice if it all goes wrong. Plus, if it works out I can always pinch the other one. There is little point in wasting good hardwood until I know that the design works. I intend to put my new oscillating bobbin sander through its paces with this design so we will see how that works too.
I have made a start by printing off six copies of the design because the box will be made from that many pieces of wood. It isn't possible to make one of these boxes from a solid piece of wood because it would be too thick to go into the scroll saw. The only option is to cut out six pieces and then glue them together. I guess that sounds simple and I suppose it is, but you have to concentrate to get it right.
I will take you through the process.
I print out the six copies of the design and then stick them onto six pieces of wood with spray mount adhesive. I then number them and do a bit of highlighting on the lines because they don't all need to be cut the same.
Piece 1 This will be the front of the box so I have highlighted the cut line in blue. I will cut out everything except the two lugs at the bottom which will be the feet and they will be only cut on pieces two and five.
Piece 2 I will cut out everything including the feet and the lines highlighted in pink which will become the insides of the draws.
Pieces 3&amd;4 are both the same and will be be cut the same as piece two with the exception of the feet.
Piece 5 This one has feet but no pink highlighting because the these will be the backs of the draws.
Piece 6 This is the easiest one. Just the outline of the box and no draws or feet because this will be the back of the box.
If that is all as clear as mud I can understand why because it makes more sense whilst actually doing it. If you read it again and try in imagine the parts being stuck together it makes more sense.
Once I have cut the pieces out on my scroll saw I will show you what I do next and that will be the subject of my next post which I promise will be coming soon.
Sorry it's been a long time between posts but I seem to have found a task that is taking all my time and then some more. I am talking about the new bathroom in the bungalow we have moved into. We had a new shower and bathroom suite fitted and in between several leaks (left by the plumbers I hasten to add) I have been doing the decorating making shelves etc which I will show you in my next post.
I may not have been using my scroll saw for craft purposes but I have been using it continuously to help with the DIY jobs.
Anyway, this week I an determined to do a scroll saw box and a bit of pyrography. The box is of my own design and a bit of an experiment because this will be my first two draw box.
I thought it would be cute to make it resemble a smiling face and I will be interested to see how it looks when it is complete. I will be making this one out of a plank of pine that was one of the side rail of my mother in law's old bed so it will be a freebee which is very nice if it all goes wrong. Plus, if it works out I can always pinch the other one. There is little point in wasting good hardwood until I know that the design works. I intend to put my new oscillating bobbin sander through its paces with this design so we will see how that works too.
I have made a start by printing off six copies of the design because the box will be made from that many pieces of wood. It isn't possible to make one of these boxes from a solid piece of wood because it would be too thick to go into the scroll saw. The only option is to cut out six pieces and then glue them together. I guess that sounds simple and I suppose it is, but you have to concentrate to get it right.
I will take you through the process.
I print out the six copies of the design and then stick them onto six pieces of wood with spray mount adhesive. I then number them and do a bit of highlighting on the lines because they don't all need to be cut the same.
Piece 1 This will be the front of the box so I have highlighted the cut line in blue. I will cut out everything except the two lugs at the bottom which will be the feet and they will be only cut on pieces two and five.
Piece 2 I will cut out everything including the feet and the lines highlighted in pink which will become the insides of the draws.
Pieces 3&amd;4 are both the same and will be be cut the same as piece two with the exception of the feet.
Piece 5 This one has feet but no pink highlighting because the these will be the backs of the draws.
Piece 6 This is the easiest one. Just the outline of the box and no draws or feet because this will be the back of the box.
If that is all as clear as mud I can understand why because it makes more sense whilst actually doing it. If you read it again and try in imagine the parts being stuck together it makes more sense.
Once I have cut the pieces out on my scroll saw I will show you what I do next and that will be the subject of my next post which I promise will be coming soon.
Wednesday, 23 April 2014
No More Felt
Hi All,
In my last post I showed you the little trinket box that I'd attacked with my pyrography iron. Here is a photo of it again so that you will be able to see what I'm talking about.
Once the pyrography work was done it still needed to be finished off and I can report that I had one success and one disappointment.
The disappointment came from the fact that I decided to save money and buy a cheaper varnish. They say that you get what you pay for and, in this instance at least, they are right. I usually buy Ronseal quick drying gloss varnish and it is very good with exception of the hole it makes in my pocket money. A small tin is in my mind quite expensive. Anyway, being the old miser that I am, while I was in the DIY superstore looking at the varnishes on offer I decided I would try their own brand because it was a couple of quid cheaper. It was a big mistake because after three coats the trinket pot still hadn't got any shine, plus I had to wait longer for each coat to dry. In the future I will stump up the cash and stick to Ronseal, that is unless anybody can recommend a good cheap varnish.
One of these days I'm going to knock the varnish on the head and polish all my projects with proper polish and I will keep you all posted when I try it out.
The success I had when finishing the box came from my felt substitute. Up until now, I have, or should I say my wife has used sticky back felt on the bottom of my boxes and the underside of the lids. I did do a couple of boxes myself but found the process of cutting out the felt and sticking it on very tedious and despite taking care it never looked great.
Happily, my days of felting are now well and truly over because I've discovered the art of flocking. Here it is on the bottom of the box and the lid. I also used it on the inside and compared with felt it was so simple to do.
Apparently, flocking has been about for years. Petrol heads use it to coat the dashboards of their cars and some female fashion trendsetters have their nails flocked.
The process is simple; an adhesive is brushed onto the area to be flocked and then small particles of material are blown onto the glue with a special applicator.
I purchased a starter set, which included the instructions, adhesive, the material and the applicator from a company called Turners Retreat who have a website of the same name. It cost me £20 but it will go a long way and if I never have to see a piece of felt again it will be well worth it.
In my next post, I will show you how I'm getting on with the box I'm making and I'll let you know how my new oscillating bobbin sander performs.
In my last post I showed you the little trinket box that I'd attacked with my pyrography iron. Here is a photo of it again so that you will be able to see what I'm talking about.
Once the pyrography work was done it still needed to be finished off and I can report that I had one success and one disappointment.
The disappointment came from the fact that I decided to save money and buy a cheaper varnish. They say that you get what you pay for and, in this instance at least, they are right. I usually buy Ronseal quick drying gloss varnish and it is very good with exception of the hole it makes in my pocket money. A small tin is in my mind quite expensive. Anyway, being the old miser that I am, while I was in the DIY superstore looking at the varnishes on offer I decided I would try their own brand because it was a couple of quid cheaper. It was a big mistake because after three coats the trinket pot still hadn't got any shine, plus I had to wait longer for each coat to dry. In the future I will stump up the cash and stick to Ronseal, that is unless anybody can recommend a good cheap varnish.
One of these days I'm going to knock the varnish on the head and polish all my projects with proper polish and I will keep you all posted when I try it out.
The success I had when finishing the box came from my felt substitute. Up until now, I have, or should I say my wife has used sticky back felt on the bottom of my boxes and the underside of the lids. I did do a couple of boxes myself but found the process of cutting out the felt and sticking it on very tedious and despite taking care it never looked great.
Happily, my days of felting are now well and truly over because I've discovered the art of flocking. Here it is on the bottom of the box and the lid. I also used it on the inside and compared with felt it was so simple to do.
The process is simple; an adhesive is brushed onto the area to be flocked and then small particles of material are blown onto the glue with a special applicator.
I purchased a starter set, which included the instructions, adhesive, the material and the applicator from a company called Turners Retreat who have a website of the same name. It cost me £20 but it will go a long way and if I never have to see a piece of felt again it will be well worth it.
In my next post, I will show you how I'm getting on with the box I'm making and I'll let you know how my new oscillating bobbin sander performs.
Tuesday, 15 April 2014
Pyrography Patterns
Hi All,
Sorry this post has been so long in the writing but I've been taking advantage of the good weather to try and sort out our new garden. Anyway, in my last post I said I would show you how I got on with the trinket pot that I was doing some pyrography on and here it is.
If you read my last post you will have seen my advice on how to break the pot up into sections to help me keep the thing symmetrical. Once I had divided the main pot into 4 sections it was just a matter of choosing a pattern that would suit pyrography. Drawing the checker board was quite simple because I just followed the same lines that divided the box into 4 sections. I used a pencil first then when I was happy I went in with the pyrography iron on a medium heat setting.
The weave pattern may look difficult but it was very easy. All you have to do is draw 4 short straight lines in one direction and then repeat the process in another direction. Try it out on a bit of scrap paper and you will be amazed how easy it is to create this pattern.
I was very pleased with the way the main pot came out but doing the lid was more difficult. I had decided to use the same two patterns that I'd used on the main pot, but had difficulty dividing the area on the lid into a suitable shape. I used the lid as a template to draw several circles on a drawing pad and then had several attempts at coming up with something that was pleasing to the eye. In the end I chose a swirling pattern after dividing the pot lid into 8 sections.
Again I was pleased with the way the pyrography turned out. If you have a go at this sort of pattern I would recommend using a spoon tip in the inverted position because it is perfect for dealing with the curve that comes on these little pots. The other thing to watch out for, is the method used to fill in the dark diamonds on the checker pattern; using short lines is easier than trying to use the back of the spoon. You will find it more accurate and you will avoid over burn which will destroy the crispness of the lighter sections.
In my next post, I will tell you how I finished the box off and reveal why using that horrible sticky backed felt is something I will never have to get involved with ever again.
Sorry this post has been so long in the writing but I've been taking advantage of the good weather to try and sort out our new garden. Anyway, in my last post I said I would show you how I got on with the trinket pot that I was doing some pyrography on and here it is.
If you read my last post you will have seen my advice on how to break the pot up into sections to help me keep the thing symmetrical. Once I had divided the main pot into 4 sections it was just a matter of choosing a pattern that would suit pyrography. Drawing the checker board was quite simple because I just followed the same lines that divided the box into 4 sections. I used a pencil first then when I was happy I went in with the pyrography iron on a medium heat setting.
The weave pattern may look difficult but it was very easy. All you have to do is draw 4 short straight lines in one direction and then repeat the process in another direction. Try it out on a bit of scrap paper and you will be amazed how easy it is to create this pattern.
I was very pleased with the way the main pot came out but doing the lid was more difficult. I had decided to use the same two patterns that I'd used on the main pot, but had difficulty dividing the area on the lid into a suitable shape. I used the lid as a template to draw several circles on a drawing pad and then had several attempts at coming up with something that was pleasing to the eye. In the end I chose a swirling pattern after dividing the pot lid into 8 sections.
Again I was pleased with the way the pyrography turned out. If you have a go at this sort of pattern I would recommend using a spoon tip in the inverted position because it is perfect for dealing with the curve that comes on these little pots. The other thing to watch out for, is the method used to fill in the dark diamonds on the checker pattern; using short lines is easier than trying to use the back of the spoon. You will find it more accurate and you will avoid over burn which will destroy the crispness of the lighter sections.
In my next post, I will tell you how I finished the box off and reveal why using that horrible sticky backed felt is something I will never have to get involved with ever again.
Sunday, 30 March 2014
New Toy
Hi All,
In my last post I mentioned my new toy which I will reveal to you today. Recently, I became interested in making bandsaw boxes with my scroll saw and here is the first one I made.
I have mentioned bandsaws and scroll saws, but because these boxes are enhanced by their sculptured lines perhaps they should be called sanded boxes. Much more time is spent sanding the wood to shape than is spent cutting with either saw.
Anyway, I managed to do quite a bit of sanding on the above box using my belt and disc sander. This is a great sander for sanding surfaces that need to be flat but for graceful curves it is not so good. I spent more than a few hours hand sanding this box to the desired shape and it played havoc with my carpal tunnel, so I decided to invest in an oscillating spindle sander. It comes with various sized drums and moves up and down while it sands. It now sits next to my disc and belt sander; its the big orange one in the photo below.
I haven't used it in anger yet, but should be able to give you a full report in my next post because I have just finished designing a new bandsaw box with two draws. I will show you that in my next post too.
Regarding pyrography, my intention is to decorate the boxes I make with pyrography patterns and that is something I'm looking forward to. In fact I have made a start on a small trinket pot that I purchased a while ago. I have divided the pot into quadrants and will fill each one with a different abstract pattern.
Dividing the pot into quadrants with a curved line may look like a difficult thing to do, but it can be made easier if you break the task down into small chunks. The away I do it is to place four pencil spots on the top rim of the box as if they were compass points, north, south, east and west. Then do the same on the bottom. Then, looking from the top, all you have to do is join top south to bottom west and carry on like that around the pot.
To aid getting the curved line symmetrical, I put a pencil dot half way between the top point and the bottom point and then just drew a simple curve between the two.Here is a picture with red spots to illustrate where I put the pencil dots before drawing the line.
Lots of drawing tasks involved in pyrography can be made a lot easier if they are broken down. Anyway, in my next post I will show you the finished pot after I've attacked it with my pyrography iron.
In my last post I mentioned my new toy which I will reveal to you today. Recently, I became interested in making bandsaw boxes with my scroll saw and here is the first one I made.
I have mentioned bandsaws and scroll saws, but because these boxes are enhanced by their sculptured lines perhaps they should be called sanded boxes. Much more time is spent sanding the wood to shape than is spent cutting with either saw.
Anyway, I managed to do quite a bit of sanding on the above box using my belt and disc sander. This is a great sander for sanding surfaces that need to be flat but for graceful curves it is not so good. I spent more than a few hours hand sanding this box to the desired shape and it played havoc with my carpal tunnel, so I decided to invest in an oscillating spindle sander. It comes with various sized drums and moves up and down while it sands. It now sits next to my disc and belt sander; its the big orange one in the photo below.
I haven't used it in anger yet, but should be able to give you a full report in my next post because I have just finished designing a new bandsaw box with two draws. I will show you that in my next post too.
Regarding pyrography, my intention is to decorate the boxes I make with pyrography patterns and that is something I'm looking forward to. In fact I have made a start on a small trinket pot that I purchased a while ago. I have divided the pot into quadrants and will fill each one with a different abstract pattern.
Dividing the pot into quadrants with a curved line may look like a difficult thing to do, but it can be made easier if you break the task down into small chunks. The away I do it is to place four pencil spots on the top rim of the box as if they were compass points, north, south, east and west. Then do the same on the bottom. Then, looking from the top, all you have to do is join top south to bottom west and carry on like that around the pot.
To aid getting the curved line symmetrical, I put a pencil dot half way between the top point and the bottom point and then just drew a simple curve between the two.Here is a picture with red spots to illustrate where I put the pencil dots before drawing the line.
Lots of drawing tasks involved in pyrography can be made a lot easier if they are broken down. Anyway, in my next post I will show you the finished pot after I've attacked it with my pyrography iron.
Tuesday, 18 March 2014
The Snake
Hi all,
Sorry for the delays between my posts, but after moving house there are hundreds of jobs waiting to be done and there aren't enough hours in the day. For almost eight weeks I've dedicated all my time to the house even though I keep telling myself that I need to have a better balance between work and play.
I will have a day off every week to do some writing I say to myself, and I will make time for pyrography and scroll sawing, but then I look at the list of jobs that need doing and I'm back to square one. However, I feel a slight shift in the air and I'm determined to put more priority into writing, pyrography, and scroll sawing. A couple of days ago I made a step in this direction whilst gaining some brownie points off my good lady wife by curing one of her problems.
Since we moved into the new house our washing machine is now in the kitchen instead of the utility room, this is a peril that comes with down sizing. Anyway, to cut a long story short, the knob on the front of her washing machine protrudes in such a way that she kept bumping it with various bits of her anatomy as she went about her daily tasks. On wash days, utterances of vile nature would pour from the kitchen as she yet again nudged the button and sent the machine into a crazy cycle that usually meant the washing would need to be started again from scratch.
She was not best pleased with this state of affairs and asked for my help regarding the solution she'd come up with. "What I need is something that I can jamb between the top of the washing machine and work surface, that protrudes further out than the knob, " she said.
Seeing an opportunity to do a bit of craft work I set about cutting a piece of wood that would do the trick. I wanted it to be slightly bulbous at one end so that it didn't have any sharp corners and I wanted a slight taper on it so that she could push it under the work surface until it gripped. I cut a piece out on my scroll saw and sanded it roughly to the shape I desire. I tried it in situ and after a few tweaks to the thickness it worked just as my wife thought it would.
However, it looked boring so I grabbed the chance to do a bit of pyrography on it. To me, the stick looked a bit like a snake, so I modified the end of it with my new sander, which I will tell you about in my next post, and then did some pyrography on it. Because time wasn't on my side, I drew what I thought a snake's head looked like on the end of the stick and burnt it in with my pyrography iron. I then gave it two coats of varnish and presented to my wife. She was chuffed and my snake now comes out at least once a week and all is well with the world.
Sorry for the delays between my posts, but after moving house there are hundreds of jobs waiting to be done and there aren't enough hours in the day. For almost eight weeks I've dedicated all my time to the house even though I keep telling myself that I need to have a better balance between work and play.
I will have a day off every week to do some writing I say to myself, and I will make time for pyrography and scroll sawing, but then I look at the list of jobs that need doing and I'm back to square one. However, I feel a slight shift in the air and I'm determined to put more priority into writing, pyrography, and scroll sawing. A couple of days ago I made a step in this direction whilst gaining some brownie points off my good lady wife by curing one of her problems.
Since we moved into the new house our washing machine is now in the kitchen instead of the utility room, this is a peril that comes with down sizing. Anyway, to cut a long story short, the knob on the front of her washing machine protrudes in such a way that she kept bumping it with various bits of her anatomy as she went about her daily tasks. On wash days, utterances of vile nature would pour from the kitchen as she yet again nudged the button and sent the machine into a crazy cycle that usually meant the washing would need to be started again from scratch.
She was not best pleased with this state of affairs and asked for my help regarding the solution she'd come up with. "What I need is something that I can jamb between the top of the washing machine and work surface, that protrudes further out than the knob, " she said.
Seeing an opportunity to do a bit of craft work I set about cutting a piece of wood that would do the trick. I wanted it to be slightly bulbous at one end so that it didn't have any sharp corners and I wanted a slight taper on it so that she could push it under the work surface until it gripped. I cut a piece out on my scroll saw and sanded it roughly to the shape I desire. I tried it in situ and after a few tweaks to the thickness it worked just as my wife thought it would.
However, it looked boring so I grabbed the chance to do a bit of pyrography on it. To me, the stick looked a bit like a snake, so I modified the end of it with my new sander, which I will tell you about in my next post, and then did some pyrography on it. Because time wasn't on my side, I drew what I thought a snake's head looked like on the end of the stick and burnt it in with my pyrography iron. I then gave it two coats of varnish and presented to my wife. She was chuffed and my snake now comes out at least once a week and all is well with the world.
Wednesday, 26 February 2014
Almost There
Hi all sorry there hasn't been any pyrography or scroll sawing posts recently, but hopefully things are about to change.
It is almost five weeks since we moved house and I have been working like a beaver every day. The bungalow we moved too is small than the previous property and getting all our belongings into it has been a mammoth task, a bit like trying to get a size 9 foot into a size 4 boot. The place as been bulging at the seams despite numerous trips to the tip (our local recycling centre) and the charity shops with stuff that my wife finds is now unsuitable for our new place
Here is a photo or the garage, that will one day soon become my new workshop. I took on the day we moved in. To be honest, this was pretty much how the whole house looked for a few days at least.
Anyway, things are looking a lot better and I hope to post a picture of my workshop soon. I can't wait to get back to the pyrography and scroll sawing so I hope it will happen in the near future.
It is almost five weeks since we moved house and I have been working like a beaver every day. The bungalow we moved too is small than the previous property and getting all our belongings into it has been a mammoth task, a bit like trying to get a size 9 foot into a size 4 boot. The place as been bulging at the seams despite numerous trips to the tip (our local recycling centre) and the charity shops with stuff that my wife finds is now unsuitable for our new place
Here is a photo or the garage, that will one day soon become my new workshop. I took on the day we moved in. To be honest, this was pretty much how the whole house looked for a few days at least.
Anyway, things are looking a lot better and I hope to post a picture of my workshop soon. I can't wait to get back to the pyrography and scroll sawing so I hope it will happen in the near future.
Subscribe to:
Posts (Atom)














